American-time Remote Transmitter 25 Watt Manuel d'utilisateur Page 1
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Horloge American-time Remote Transmitter 25 Watt. American Time Remote Transmitter 25 Watt User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Your SiteSync IQ system is now set up for proper operation.
For information on other features, see the Installation and
Operation Manual that was included with your system. If you
have any questions, please contact Technical Support at
American Time: 800-328-8996.
6
Activate & hang your clocks
Don't activate the battery or apply power to the clocks until the Remote Transmitter is installed and
transmitting and the clock is in the intended location.
American Series Digital Clocks
1. Take the clock to the area where it will be used.
2. To activate the clock, connect to AC power.
3. Display will ash “U40” or 1:00 o’clock until it
receives a signal.
4. Verify synchronization takes place within 2-5
minutes.
SiteSync IQ
®
Remote Transmitter with Campus TX Antenna
INST-SSQRTM-X-E Rev 2
Please read this rst!
After determining the proper wattage for your facility, we guarantee the coverage of your Remote
Transmitter when you follow a few simple steps. If this is your rst installation or you have questions at
any time during this process, please call American Time toll free at 800-328-8996.
We're here to help!
This Quick Start Guide will help you avoid three common installation mistakes:
1. Improper location of transmitting (TX) antenna. A temporary install of the Remote Transmitter
is recommended.
Don't drill holes for permanent installation and mounting until the system is working correctly.
2. Improper Remote Transmitter start-up. A successful transmission is indicated by the PTT and
DATA LED's ashing on the front of the unit.
Don't locate the campus TX antenna within 4' of the remote transmitter.
3. Improper clock start-up. Activate clocks in their intended location.
Don't activate the clocks in one room and move them to another location as signal reception
will not be veried. Make sure the Remote Transmitter is transmitting and is not in Quiet Mode.
Important Note: Clocks should be installed within 24 hours of installing the Remote Transmitter.
After 24 hours, the Remote Transmitter will enter Quiet Mode. To disable Quiet Mode, reference
the Remote Transmitter Installation and Operation Manual section Remote Transmitter Connect
Configuration tab step 5 and Appendix F.
AC
DC
To
wiring
box
Reset
Button
LED
Electric
Electric (AC) Analog Clocks
1. Take the clock to the area where it will be used.
2. To activate the clock, connect to AC power.
The LED on the back of the clock (see below)
will ash red within 30 seconds of power-up to
indicate receiver is looking for the wireless
signal.
When the signal is received, the LED will ash
green. Be patient. The clock hands will rapid
advance to the correct time. This may take
up to 15 minutes.
3. Hang the clock once signal reception is
veried and clock is operating correctly.
Note: If the LED does not ash within 30 seconds,
disconnect the barrel plug on the clock receiver, wait
10 seconds and reconnect. The LED will begin ashing
within 30 seconds.
Activation Note: Clocks should be installed within 24 hours of
installing the Remote Transmitter. After 24 hours, the Remote
Transmitter will enter Quiet Mode. To disable Quiet Mode
reference the Remote Transmitter installation and Operation
Manual section Remote Transmitter Connect Configuration tab
step 5 and Appendix F.
phone: 800-328-8996 fax: 800-789-1882 online: american-time.com
mail: 140 3rd St. So.; PO Box 707, Dassel, MN 55325-0707
AC
DC
To
wiring
box
LED
Battery
Barrel
Jack
Input
Battery Analog Clocks
1. Take the clock to the area where it will be
used.
2. To activate the clock, connect barrel jack plug
of battery pack to wireless receiver. The
LED on the back of the clock will ash red
within 30 seconds of power-up to indicate
receiver is looking for the wireless signal.
When the signal is received, the LED will ash
green. Be patient. The clock hands will rapid
advance to the correct time. This may take up
to 15 minutes.
3. Hang the clock after hands are rapid
advancing.
Note: If the LED does not ash within 30 seconds,
remove the barrel jack plug of the battery pack from
the wireless receiver for 5 seconds and reconnect it.
This resets the receiver. The LED will begin ashing
within 30 seconds.
1
2
Résumé du contenu
Page 1 - Please read this rst!
Your SiteSync IQ system is now set up for proper operation. For information on other features, see the Installation and Operation Manual that was incl
Page 2 - REMOTE TRANSMITTER
abcdefghijklmnQUICK START INSTALLATION GUIDE SITESYNC IQ® REMOTE TRANSMITTER Connect cables to the Remote Transmitter A. Connect a CAT 5 or highe
Produits connexes et manuels pour Horloge American-time Remote Transmitter 25 Watt
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.502 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels